高新技术企业 · 汽车深度养护品专业供应商

全国招商电话:13318861726

汽车养护
进入淘宝店
当前位置:首页 > 产品中心 > 固诺-K33快蜡固诺
K33快蜡

采用最先进的汽车去划痕技术,可以迅速磨除1500#-2000#砂纸痕,抛光蜡尘极少,同时具有增艳功能。

  • K33快蜡

品牌:固诺

系统:全车防锈

K33快蜡

产品编号:KL.02.Z077

企业标准:Q/YK 024-2009

仅供4S店使用


产品特点:

采用最先进的汽车去划痕技术,可以迅速磨除1500#-2000#砂纸痕,抛光蜡尘极少,同时具有增艳功能。


产品功能:

1、快速修复漆膜因操作失误引起的缺失。

2、除去经1500#-2000#砂纸的打磨痕迹。

3、除去尘粒,流挂,过量喷漆及橙皮纹等。

4、可以修复陈旧漆磨氧化表面,回复漆膜高度光泽。


使用方法:

1、为避免漆面过于干燥, 建议在漆面完成喷涂后24小时内进行湿磨平整.

2、按个别情况而选择研磨砂纸的粗细级别(本产品可去除#1000以上的湿磨砂纸划痕*)

3、如需快速有效地去除砂纸痕, 建议采用中到中粗羊毛球(注: 若采用粗/中粗海绵垫亦可, 但去痕速度会有差异.)

4、在羊毛球/海绵球上, 倒上大约2寸直径圆形范围的蜡. (注意: 在开始打磨的羊毛球/海绵球会较为干燥, 但当打磨一段时间后, 会有一定份量的粗蜡囤积在羊毛球/海绵垫的表面, 当表面积聚一定的粗蜡后, 用量会减少.)

5、用专业高速抛光机进行研磨, 速度应设在约1800转/分钟, 方向应由左上方开始, 到右上方, 打磨面积在一开始设定在2’x2’的范围. 从左到右, 然后向下移动约5’’, 再从左到右. 切记羊毛球/海绵垫须平贴在漆面上, 否则 非常容易在漆面上留有螺旋纹.

6、打磨2’x2’’面积2-3次, 若粗蜡开始干燥, 可喷水雾再活化粗蜡进行二次研磨.

7、继续研磨至粗蜡耗尽, 然后用柔软的纳米/微纤维布抹擦漆面.


Properties:

With the most advanced automobile denotching technology, it can quickly remove 1500-2000 # sandpaper marks, and the polishing wax dust is very little.


Product functions:

1. Quick repair of the missing paint film caused by operation error.

2. Remove the polishing marks of 1500-2000 # sandpaper.

3. Remove dust particles, flow hanging, excessive paint spraying and orange peel lines, etc.

4. It can repair the surface of the old paint and restore the high gloss of the paint film.


Usage:

1. In order to avoid excessive dryness of the paint surface, it is recommended to conduct wet grinding and leveling within 24 hours after the painting is finished.

2. Select the thickness of abrasive paper according to individual cases (this product can remove more than #1000 wet abrasive paper scratches *)

3. If sandpaper marks need to be removed quickly and effectively, it is recommended to use medium-thick wool balls (note: if thick/medium-thick sponge pads are adopted, the mark removal speed will be different).

4, on the wool/sponge ball, pour over about 2 inches in diameter circular range of wax. (note: at the beginning of the grinding ball of wool/sponge ball is relatively dry, but when polishing after a period of time, there will be a certain amount of coarse hoard wax on the surface of wool ball/rubber cushion, after the surface accumulated certain coarse wax, consumption will be reduced.)

5, with professional high-speed grinding polishing machine, speed should be located in about 1800 r/min, the direction should start from the top left, to the upper right, polishing area in the first set in the range of 2 "x2". From left to right, then move down about 5 ", then from left to right. Remember that wool ball/cushions should be flat on the paint surface, otherwise very easy with spiral lines on the surface of the paint.

6. Polish the area of 2 'x2' 2-3 times. If the crude wax starts to dry, spray water mist and reactivate the crude wax for secondary grinding.

7. Continue grinding until the crude wax is exhausted, then apply a soft nano/micro fiber cloth to the finish.





空调清洗剂