高新技术企业 · 汽车深度养护品专业供应商

全国招商电话:13318861726

汽车养护
进入淘宝店
当前位置:首页 > 产品中心 > AKO 爱蔻 > 冷却系统-爱蔻发动机环保冷却油冷却系统
爱蔻发动机环保冷却油

采用浓缩性全合成油,能有效地降低温度,沸点高。 

爱蔻发动机环保冷却由美国ubrizol-AKO、美国陶氏公司提供原料原料及技术支持,扎根中国汽车养护用品研发一级学府--华南理工大学化工系,精心研发而成!


  • 爱蔻发动机环保冷却油

爱蔻发动机环保冷却油

品牌:AKO爱蔻

系统:冷却系统

爱蔻发动机环保冷却油

产品编号:AKO-115-4L/4L

企业标准:Q/YK 046-2011

产品仅供4S店使用

本品采用高沸点结合高效的抗泡配方,并参考德国国家实验室冷却剂抗腐技术,由高级多元醇,抗氧剂,防气蚀剂等多种添加剂精制而成



产品特性:

1、沸点高 、冰点低 ;(工作温度-60℃ ~180℃), 不结冰耐严寒 ,彻底消除 “开锅”烦恼,热车可随时打开水箱盖。

2、无铁锈、无水垢、无腐蚀、无气蚀、无蒸发,无压力。 延长了发动机部件的使用寿命,减少维修和更换。

3、有效的改善和平衡了发动机的温度,减少了发动机的磨损,提升发动机性能。

4、缩短发动机起动时升至正常温度的时间,降低发动机噪音,减少废气排放。

5、消除汽缸顶部“过热顶点”现象,防自燃、防爆震。 增加扭矩, 增强动力、 降低油耗 。

6、高品质产品,一次加注,经久耐用,使用寿命超过50万公里,真正无需更换的冷却油。使用方法:


1、施工对象:新车、磨合期后的车


2、施工操作流程:

(1)、车辆进入工位后打开暖风,对发动机进行常规检查:发动机水温、故障灯、暖风情况、冷却系统检漏。(如有渗漏维修后再操作)

(2)、拧开放水开关或拆开下水管,把原车冷却水放掉,拧紧放水开关或装好下水管。

(3)、等发动机降温后往水箱里加进清水,起动发动机让冷却系统进行清洗,清洗过程加油门让节温器打开(不开空调时风扇转动)

(4)、清洗完成后拧开放水开关把水放掉,拆开上、下水管,暖风管、中缸放水螺丝、副水箱(若螺丝太紧建议不拆),有双空调的车型,还需拆除后排暖风管。

(5)、等发动机降温后用清水清洗整个冷却系统一遍,如水箱、缸休、暖风箱、副水箱等。

(6)、用AKO专业风枪把冷却系统的水吹干净。吹水流程:(1)吹干净水箱内的冷却水。(2)吹干净缸体内的的冷却水。(3)吹干净暖水箱内的冷却水(保证出水管无水珠则可)。

(7)往中缸加注500毫升爱蔻除水剂,用风吹出来(用杯接住),用测水仪测含水量(须测3次以上)仪器刻度达53以上,再把缸休中的除水剂吹干净。

(8)、拧紧放水开关,装上上、下水管、暖风管、中缸放水螺丝(注:留一条位置高的管不装,加注无水冷却油时让它排空气),清洗吹干后装上副水箱。

(9)、往水箱里添加无水冷却油,添加过程用手指捏上下水管进行排空(如该车型有放空螺丝则拧开螺丝进行排空),当水箱里的冷却油加满时,起动发动机踩油门让节温器打开(加速到2500转/分,密切留意水温变化及管道状况)。

(10)、再往水箱及副水箱添加无水冷却油直到标准液面,拧上水箱盖道路试车,路试后打开水箱盖测无水冷却油中的水含量,仪器刻度达53以上,并检查无水冷却液的液面高度(不够时添加到标准液面)。

(11)、检查各水管有没漏水,冷却系统是否正常,在水箱盖和车尾贴上AKO发动机环保冷却油警告标志,以免再次加入传统冷却液和水。


注意事项:

(1)、换了AKO发动机环保冷却油之后不能添加水或其他冷却液,以免影响产品的最佳性能发挥。

(2)、行车时发现冷却液不够发动机温度偏高,这时车上没有AKO冷却油,则可以添加一些纯净水先解燃眉之急,然后有条件时再把冷却液彻底更换成AKO冷却油,恢复原车性能。


Engine environmentally friendly cooling oil


Product features:

1, high boiling point ℃, and eliminate the "KaiGuo" worry; Realize the cooling system under pressure of high temperature without cooling;

2, low freezing point-60 ℃, not icy cold resistance;

3, no scale, no corrosion, no evaporation, extended the engine cooling components used in life, reduce maintenance and replacement;

4, derusting, in addition to scale, clean engine cooling system;

5, improve and balance the engine temperature, reduce the engine wear;

6, shorten the engine start to normal temperature of time, reduce the waste gas pollution;

7, improve the power, increase the torque, reduce oil consumption, reduce the pollution;

8, practice proves optimal way engine cooling oil environmental protection service life more than kilometers, still effective, and can be duplicated.



Method of use:

1, construction condition:

A, km above the vehicles, before construction must use AKO cooling system treatment of cooling system for A thorough cleaning.

B, a new car or a 30000 km on the following vehicles are not clean.


2, operation process:

(1), prepare the cooling system treatment.

(2), open water tank cover the detergent directly into water tank, starting engine clean 10 minutes, the cleaning process must let go door WenQi Open Day.

(3), cleaning after the completion of the shut down engine, twist the open water switch, the cooling water drop.

(4), Water switch on

(5) the water on the switch, and went to inclAKOe water tank, starting engine clean 3-5 minutes, cleaning process must let's day WenQi open

(6), cleaning after the completion of the open water switch to twist water, dismantle,hoses, warm wind tube (has a double air conditioning models, still to be removed in the warm wind tube)

(7), with the professional FengQiang AKO cooling system of water blow clean.


Blow water flow:


(1) the blow of filtered water cooling water.

(2) clean the cylinder of the blow cooling water.

(3) blow clean water tank warming of the cooling water (blew warm water tank, need to open the warm wind, temperature moves to switch the biggest)

(8), the water on the switch, pack up and, hoses, warm wind tube.

(9), tear open next vice water tank, cleaning loaded on vice water tank.

(10), to add the water tank no water cooling oil, add process using fingers are emptying and conduit (such as the model, the vent screw is a twist screws are emptying), when the cooling in the water tank filled with oil, starting the engine accelerator let's day WenQi open, to add cooling water tank and vice water tank oil until standard liquid surface.

(11), screw in water tank cover road test, and the road test must open the water tank cover without water cooling fluid check liquid surface height, when not added to the standard liquid surface.

(12), check the water pipes have no leak, the system is normal or not, in the water tank cover and the AKO engine cooling oil with environmental protection warning signs, lest again to join the traditional cooling fluid and water.


Note:

(1), changed the AKO engine cooling oil environmental protection after can not add water or other liquid cooling, lest affect the product's best performance.

(2), driving found cooling fluid enough engine temperature on the high side, then the car without AKO cooling oil, can add some water first the solution is having some trouble, then conditional when put cooling fluid replacement thoroughly into AKO cooling oil, restore the original car performance.

空调清洗剂